Search Results

Search found 33898 results on 1356 pages for '11 10'.

Page 100/1356 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• How can I install mysql 5.0 on Ubuntu 10.04?

  - by Tyler Smart

  Hi, Is there any repo that will let me install mysql 5.0.51a on Ubuntu 10.04, or do I have to install it from scratch? Sincerely Tyler

  Read the article

• Antialias not working in ubuntu lucid lynx 10.04

  - by mac

  I have recently upgraded from karmic to lucid (plain ubuntu using gnome). Everything worked fine, but the characters now aren't anti-aliased any more, as you can appreciate from the screenshot: This is what I tried to fix the situation, unluckily without succeeding: Used the regular option pane from System-Preference-Appearance-Font (smoothing, hinting...) Edited the .fonts.conf file Disinstalling (and then re-installing) the mstcorefont package Changing the default Sans font to a font of my liking (e.g. Tahoma) from the abovementioned Appearance options My ubuntu installation is quite standard, with the typical add-ons one might wish for usability. I used the ubuntu start script to make a few tweaks. Thank you in advance for your help! :)

  Read the article

• Can't get .htaccess to work

  - by orokusaki

  I'm using Apache2 on Ubuntu Lucid Lynx. I have config set to use .htaccess like normal. This is my default site: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> I've tried lower case "all" (AllowOverride all) as well. My .htaccess file looks like this: //Rewrite all requests to www Options +FollowSymLinks RewriteEngine on RewriteCond %{HTTP_HOST} ^mydomain.com [nc] RewriteRule ^(.*)$ http://www.mydomain.com/$1 [r=301,nc] //301 Redirect "old_junk.html" File to "new_junk.html" Redirect 301 /old_junk.html /new_junk.html //301 Redirect Entire Directory "old_junk/" to "new_junk/" RedirectMatch 301 /old_junk/(.*) /new_junk//$1 // Copy and paste redirect examples from above: (with mydomain replaced with my actual domain... and my computer is plugged in)

  Read the article

• Internet connection sharing: Ubuntu 9.10 Server on Windows 7 and VMWare

  - by avesse

  I'm trying to get Internet Connection Sharing (ICS) working between my Windows 7 RTM host and a Ubuntu 9.10 Server running on VMWare Workstation 6.5, but I have not been able to get it right. Here's what I have done: Configured VMWare to use Host Only networking (I tried NAT as well). Enabled ICS on my host's network connection, allowing VMnet1. After enabling it, Windows informed me that its VMnet1 IP has changed to 192.168.137.1. So in VMWare's Virtual Network Editor I configured VMnet1: Subnet 192.168.137.0 Mask 255.255.255.0 I did the same for DHCP. For NAT i set 192.168.137.1 as Gateway. I cannot ping any sites or get access through apt-get/aptitude install/update, although domains do get resolved to IPs. I have also tried using a static IP in Ubuntu. I don't know if it makes a difference, but my external IP is locked to my host's MAC address.

  Read the article

• Disable visual system beep on Karmic

  - by pzico

  Some programs are about to make me epileptic with excessive screen flashing/blinking (terminator etc.). In Ubuntu Hardy Heron I could solve the problem by unchecking System-Preferences-Sound-System Beep-Visual system beep. However on Karmic Koala there is no such option. I googled and found many solutions for turning off visual beep/bell. However nothing seems to work. So my question is that what is the exact alternative to disable Visual system beep on Karmic?

  Read the article

• How to enable Chess 3D on Ubuntu 9.10?

  - by Jian Lin

  The 3D cannot be easily enabled. A thread that people refer to is http://ubuntuforums.org/showthread.php?t=416660 but I tried several suggestions on that thread and it doesn't work yet. The message is: No Python OpenGL support No Python GTKGLExt support

  Read the article

• Virtual Box, Virtual Mac on Ubuntu Karmic ?

  - by Arkapravo

  Dear Friends I have been trying to virtualise Mac OS-X 10.5 Leopard (I used an iso) on my Ubuntu 9.10 Karmic Koala. Which has yielded no success ! ..... can OS-X be the guest OS in Virtual Box ? Has anyone done it, are there any legality issues Regards Arkapravo

  Read the article

• Ubuntu 10.04 Installation

  - by Sarang

  I do have XP on my PC. I want to shift to Ubuntu 10.04. I want to format whole PC & want to keep only Ubuntu. Should I have to keep partition for it like we do in previous version of Ubuntu. Doesn't it waste my space ?

  Read the article

• Moving new drive volume out of /media

  - by nomoreflash

  I have the following filesystem: Filesystem Size Used Avail Use% Mounted on /dev/sda1 33G 2.7G 29G 9% / udev 1007M 232K 1007M 1% /dev none 1007M 244K 1007M 1% /dev/shm none 1007M 292K 1007M 1% /var/run none 1007M 0 1007M 0% /var/lock none 1007M 0 1007M 0% /lib/init/rw none 33G 2.7G 29G 9% /var/lib/ureadahead/debugfs /dev/sdb1 137G 69M 137G 1% /media/New Volume I want the /media/New Volume to become part of /. Does anyone know how I can do that without using gparted etc.?

  Read the article

• Ubuntu 10.04 upgrade: gdm-simple-greeter no seat-id found

  - by Broam

  Upgraded a machine straight from Ubuntu 8.04 to 10.04. After a successful upgrade, GDM shows no users on the login screen, with the error message: "gdm-simple-greeter no seat-id found" Users can log in via text mode. A recovery user can startx without issue. I'm convinced this is an issue with GDM and/or ConsoleKit. What are my options? I've debated a reinstall but would rather not. I've also thought of switching to KDM or XDM instead. I've filed a launchpad bug--no responses yet.

  Read the article

• Ubuntu 10.04 LTS - good enough to jump on it?

  - by iconiK

  I'm currently planning to get a VPS from VPS.net for a PHP project. I personally haven't used CentOS (which is recommended all the time) and this is not a good time for me to start learning it, so I want to stick with Ubuntu, as that's the one I have experience with. Now there's the good ol' 8.04 LTS that's well supported, however, 10.04 LTS was released two days ago. I installed it on my laptop and it is pretty slick (doesn't matter for a server) and quick. But I am skeptical about it: Has anyone tried it in a production environment so far? How does it perform versus 8.04? Any serious bugs so far?

  Read the article

• pdf printer in wine ?

  - by Arkapravo

  I wish to convert (print) my MS Word files to pdf on the fly ! I am on Ubuntu 9.10 and using Wine 1.1.40. Can someone help ? I have heard that pdf printer can be installed using Wine Cups ! Thanks !

  Read the article

• VMWare Server 2.0.2 on Ubuntu 10.04?

  - by Robert S. Barnes

  Does VMWare's free Server 2.0.2 run on Ubuntu 10.04 yet? Or do they have a similar free product that runs' on Ubuntu 10.04?

  Read the article

• Updating Dell PowerEdge firmware on Ubuntu?

  - by Shtééf

  The company I work for recently got hands on a batch of second hand PowerEdge SC1425 machines. We'd like to put these to good use. Our operating system of choice is Ubuntu Server 10.04 64-bit, which installs just peachy on this type of machine. Now I'd like to install the firmware updates from Dell, which are apparently marked as recommended. This includes the updates for the BIOS, the BMC, and possibly some other hardware. I find it incredibly difficult to locate the files on the Dell website, and install any of them on an Ubuntu system: I downloaded the file OM_6.2.0_SUU_A01.iso. I believe I've read that the SUU DVD should be able to update any recent PowerEdge. Is this correct? Is this the latest version? Besides the version number, does A01 have any meaning? Is this image bootable? (At the moment, I just nosed around with a loop device mount.) Running /bin/bash ./suu from the DVD, I get: # /bin/bash ./suu ./suu: line 262: ./java/linux/i386/bin/java: No such file or directory The file exists and is executable, though. But I cannot execute it directly from the shell either.

  Read the article

• Linux policy routing - packets not coming back

  - by Bugsik

  i am trying to set up policy routing on my home server. My network looks like this: Host routed VPN gateway Internet link through VPN 192.168.0.35/24 ---> 192.168.0.5/24 ---> 192.168.0.1 DSL router 10.200.2.235/22 .... .... 10.200.0.1 VPN server The traffic from 192.168.0.32/27 should be and is routed through VPN. I wanted to define some routing policies to route some traffic from 192.168.0.5 through VPN as well - for start - from user with uid 2000. Policy routing is done using iptables mark target and ip rule fwmark. The problem: When connecting using user 2000 from 192.168.0.5 tcpdump shows outgoing packets, but nothing comes back. Traffic from 192.168.0.35 works fine (here I am not using fwmark but src policy). Here is my VPN gateway setup: # uname -a Linux placebo 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux # iptables -V iptables v1.4.12 # ip -V ip utility, iproute2-ss111117 IPtables rules (all policies in table filter are ACCEPT) # iptables -t mangle -nvL Chain PREROUTING (policy ACCEPT 770K packets, 314M bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 767K packets, 312M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 5520 packets, 1920K bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 782K packets, 901M bytes) pkts bytes target prot opt in out source destination 74 4707 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner UID match 2000 MARK set 0x3 Chain POSTROUTING (policy ACCEPT 788K packets, 903M bytes) pkts bytes target prot opt in out source destination # iptables -t nat -nvL Chain PREROUTING (policy ACCEPT 996 packets, 51172 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 7 packets, 432 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1364 packets, 112K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 2302 packets, 160K bytes) pkts bytes target prot opt in out source destination 119 7588 MASQUERADE all -- * vpn 0.0.0.0/0 0.0.0.0/0 Routing: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master lan state UNKNOWN qlen 1000 link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff valid_lft forever preferred_lft forever 3: lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff inet 192.168.0.5/24 brd 192.168.0.255 scope global lan inet6 fe80::240:63ff:fef9:c38f/64 scope link valid_lft forever preferred_lft forever 4: vpn: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100 link/none inet 10.200.2.235/22 brd 10.200.3.255 scope global vpn # ip rule show 0: from all lookup local 32764: from all fwmark 0x3 lookup VPN 32765: from 192.168.0.32/27 lookup VPN 32766: from all lookup main 32767: from all lookup default # ip route show table VPN default via 10.200.0.1 dev vpn 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 # ip route show default via 192.168.0.1 dev lan metric 100 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 TCP dump showing no traffic coming back when connection is made from 192.168.0.5 user 2000 # tcpdump -i vpn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vpn, link-type RAW (Raw IP), capture size 65535 bytes ### Traffic from user 2000 on 192.168.0.5 ### 10:19:05.629985 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6887764 ecr 0,nop,wscale 4], length 0 10:19:21.678001 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6891776 ecr 0,nop,wscale 4], length 0 ### Traffic from 192.168.0.35 ### 10:23:12.066174 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [S], seq 2294159276, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 557451322 ecr 0,sackOK,eol], length 0 10:23:12.265640 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [S.], seq 2521908813, ack 2294159277, win 14480, options [mss 1367,sackOK,TS val 388565772 ecr 557451322,nop,wscale 1], length 0 10:23:12.276573 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [.], ack 1, win 8214, options [nop,nop,TS val 557451534 ecr 388565772], length 0 10:23:12.293030 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [P.], seq 1:480, ack 1, win 8214, options [nop,nop,TS val 557451552 ecr 388565772], length 479 10:23:12.574773 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [.], ack 480, win 7776, options [nop,nop,TS val 388566081 ecr 557451552], length 0

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by develop7

  Preface: I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator tells "Logon failure" upon connect attempt. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by Develop7

  Intro I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 Problem But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator screams "Logon failure" upon connect attempt, and, respectively, fails to connect. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d Question So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• bind9 DNS Ubuntu names pingible on server, but not on Windows Machines?

  - by leeand00

  I setup a DNS server today on Ubuntu, following this tutorial. My intent was to setup my network for dns-name resolving on the private LAN within a single zone (nothing fancy I just want name resolution). I've tested the setup on the DNS server machine itself, and I can ping all the machines listed in the configuration file. I've also configured the Windows Machines on my network, and for some reason they are incapable of pinging by names as was possible on the DNS Server itself. I've tried running nslookup on the Windows DNS clients and I receive and error mentioning the address of the DNS server. DNS forwarding works fine, I'm not having any trouble accessing the internet, the problem only lies within accessing names within the private LAN. Here are my configuration files: options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { 8.8.8.8; 8.8.8.4; 74.242.0.12; //68.87.76.178; }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.options zone "leerdomain.local" { type master; file "/etc/bind/zones/leerdomain.local.db"; notify no; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.2.168.192.in-addr.arpa"; notify no; }; /etc/bind/named.conf.local Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 2010011001 28800 3600 604800 38400 ); leerdomain.local. IN NS ns.leerdomain.local. ns IN A 192.168.2.9 asus IN A 192.168.2.254 www IN CNAME asus vaio IN A 192.168.2.253 iptouch IN A 192.168.2.252 toshiba IN A 192.168.2.251 gw IN A 192.168.2.1 TXT "Network Gateway" /etc/bind/zones/leerdomain.local.db (Validates fine with named-checkzone when validating zone leerdomain.local) Reverse Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 201001101 28800 604800 604800 86400 ) IN NS ns.leerdomain.local. 1 IN PTR gw.leerdomain.local. 254 IN PTR asus.leerdomain.local. 253 IN PTR vaio.leerdomain.local. 252 IN PTR iptouch.leerdomain.local. 251 IN PTR toshiba.leerdomain.local. /etc/bind/zones/rev.2.168.192.in-addr.arpa *(Does not validate with named-checkzone when validating zone leerdomain.local gives an error of: zone leerdomain.local/IN: NS 'ns.leerdomain.local' has no address records (A or AAAA) zone leerdomain.local/IN: not loaded due to errors. * Despite not validating bind9 starts without errors in /var/log/syslog I've also configured a few of the windows machines on my network to have the static ip as specified in the lookup and reverse lookup config files. i.e. Using nslookup yields the following results: C:\Users\leeand00>nslookup ns Server: UnKnown Address: 192.168.2.9 *** UnKnown can't find ns: Non-existent domain C:\Users\leeand00>nslookup gw Server: UnKnown Address: 192.168.2.9 Name: gw. Additionally trying to ping by name also fails on machines that are not the DNS Server. Is there something wrong with my configuration of either the nameserver or the Windows Boxes that is keeping me from accessing other machines using names?

  Read the article

• How to format DVD-RAM?

  - by AndrejaKo

  I have few DVD-RAM disks and when using udftools, specifically sudo mkudffs --media-type=dvdram /dev/sr0 where /dev/sr0 is my DVD-RAM drive, I get trying to change type of multiple extents and nothing happens. What should I do? EDIT After trying with dvd+tools, here's what I got: #dvd+rw-format /dev/dvd -format=full -ssa=default * BD/DVD±RW/-RAM format utility by <[email protected]>, version 7.1. * 4.6GB DVD-RAM media detected. * formatting 54.8| And same error as before from mkudffs.

  Read the article

• wpa_supplicant on lucid

  - by Thiago

  Hi, I'm trying to get my wifi working through the command line, but I'm not having success. I generated the wpa_supplicant.conf with wpa_passphrase and I'm running wpa_supplicant -Dwext -iwlan0 -c /etc/wpa_supplicant.conf. I only receive as a clue "Disconnect event - remove keys" and I get associated. What can I do?

  Read the article

• How to add higher video resolution in Ubuntu 10.4 (UNR on EEE1101HA)

  - by lexu

  I picked up an ASUS EEE 1101HA with Windows 7 and installed UBUNTU 10.4 Netbook Remix (dual boot). Ubuntu runs fine, but it doesn't recognize that the notebook LCD is 1388x768 and thus only offers 1024x768 and 800x600 as monitor resolution. So .. how can I tell it about that higher resolution? (Have root pwd & vi, una-bash-ed to use both.. )

  Read the article

• Huge host CPU usage in idle vmware guest. Ubuntu 10.04 host, Vista SP2 guest

  - by themesandmodules

  I'm experiencing huge host CPU usage with an idle vmware guest. Host: Ubuntu 10.04 32-bit 2.6.32-24-generic-pae. (Very new install, i.e 24 hours ago) Hardware is Dell XPS M1530 laptop, 4GB ram. Intel Core II Duo T9300 2.50Ghz The virtualization setting "VT" or something is enabled in my bios. Guest: Completely fresh install of Windows Vista, upgraded to latest SP2 and all windows updates installed. 1024 - 1512MB ram allocated. Absolutely no other software installed on it, apart from VMWare tools. Situation When the guest is doing absolutely nothing, I watch with sysinternals process watch on the guest. This shows that system idle process is between 70 and 99%, usually around 95%. No actual process doing anything. On the host, I watch with top, I get cpu usage of 20% - 80%, usually around 30%. What I have tried Single and Dual processor available to guest - no change. Turn off all peripherals to guest - no network, drives, usb etc - no change. Turn off 3d acceleration for guest - perhaps a small improvement, or no change. Upping allocated ram to guest from 1024MB to 1512MB - no change. Yelling at vmware - no change. I have experienced a similar issue in the past, which was solved by setting the guest to have 1 CPU. This time that hasn't worked.

  Read the article

• Microsoft Robotics Studio in Ubuntu, with Wine ?

  - by Arkapravo

  I am using Ubuntu 9.10 and I am a bit of a robotics enthusiast. I have used KiKS (in MATLAB for simulating Khepera robots), MobotSim (in Windows, simulates a point like robot using a BASIC editor) and Player/Stage (with C/C++ on Ubuntu 9.04). My question, can MS Robotics Studio be installed in Ubuntu Linux using Wine (I am using 1.1.31) ? Has anyone done it ? Any other way to install MS Robotics Studio in Unix (Any flavour) ? Thanks for your reply !

  Read the article

• What could cause a huge packet loss in Ubuntu 9.10, for both wired and wireless?

  - by xzenox

  I was previously using 9.04 fine (and in fact, I am posting this from my old 9.04 live cd). I tested the following install steps in a virtualbox vm prior to following the sames ones to upgrade my laptop: Download/burn ubuntu minimal cd (12mb one) Install ubuntu minimal sudo apt-get update sudo apt-get upgrade sudo apt-get ubuntu-desktop ubuntu-standard In the VM worked fine and I found myself with a working 9.10 ubuntu, network worked fine and I was able to test my backups and DropBox without a hitch (host was 9.04). When I followed the same steps on my laptop, everything worked up to after 9.10 being installed and working. As far as I can tell, everything besides eth0/wireless works. For some reason, I am unable to access the internet. Ping reports that over 99% of packets get lost (over an hour or so of pinging). This means for example that if I try hard enough, I can load a webpage but only at the cost of much patience... This happens both for a wired and wireless connection to my wrt310n (updated with latest firmware). At first I thought that it could be related to the ipv6 issues ppl have been experiencing however even after disabling ipv6 at the kernel level (through grub), I still get the issue. I do not think this is related to DNS issues or the likes since even when I ping my ISP's gateway IP, I have the same amount of packet loss. No DNS resolving should be required there. Access to my router works peachy with no packet loss there. I've tried different MTU values but to no avail. Note that this issue affects every web-enabled application: firefox, ping, synaptic, etc. The same hardware/router combo works with 9.04 but not with 9.10. In fact, when I did: sudo apt-get ubuntu-desktop ubuntu-standard after 9.10 minimal was installed, it downloaded over 400mb of packages without a hitch so my guess is that one of those packages either in ubuntu-desktop or ubuntu-standard is causing havok. Thoughts?

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >